标签存档： 太阳能路灯制造商

勒克斯级别

太阳能路灯照度标准。我需要什么照度？

/于 /由

太阳能街道照明系统的光测量

亮度有两个重要指标 太阳能路灯、拉克斯（Lux）和流明（Lumens）。
勒克斯和流明都是亮度的测量单位。它们用来告诉我们特定表面的照明输出量和光照亮度。

流明等于光输出。
勒克斯（用 lx 表示）代表单位面积的光通量。

流明和勒克斯之间的关系：1 勒克斯等于每平方米 1 流明（lm/m2）。
流明和流明在本篇文章中，我们将探讨路灯的流明标准及其重要性。如果您想了解流明，可以查看这篇文章：了解瓦特和流明：如何为项目选择合适亮度的灯具

什么是照明中的勒克斯，为什么它很重要？

勒克斯是对落在物体表面的光通量的测量。勒克斯是光度学的国际单位，是一种测量光强度的方法。勒克斯用于指定光或照明的亮度。它是所有类型照明（如家用照明、办公室照明、汽车前灯或路灯）的标准光测量单位。

道路照明标准

为什么勒克斯水平比流明更有意义

流明测量单个光源的光输出。流明测量的计算方法是用光源的瓦数乘以每瓦光源的额定流明。

勒克斯是表面上的光量。这可以通过光传播一定距离后的亮度来测量。

除了亮度之外，勒克斯级也是测量太阳能路灯亮度的最佳方法。照度测量只需使用照度计即可轻松完成，而亮度测量则需要专业设备，实施起来较为困难。
现在，如果有一个亮度为 1000 流明的太阳能路灯灯泡，将其放置在 10 米之外，其亮度就会不同。因此，改变灯泡的位置会改变不同勒克斯水平下的亮度。流明测量灯泡产生的光量，勒克斯测量光传播的距离。

不同道路太阳能路灯照明的 Lux 值

我需要多高的照度？

根据一些国家政府文件规定的标准，我们提出以下建议作为参考：

公路照明 勒克斯级别

太阳能路灯

一级公路、二级公路最低平均照度维持值为 20 lx（低标准）/30 lx（高标准），均匀度最低值为 0.4；

三级公路最低平均照度维持值为 15 lx（低标准）/20 lx（高标准），均匀度为 0.4；
四级道路：平均照度 10 lx（低标准）/15 lx（高标准），均匀度 0.3；

上述照度要求仅适用于沥青路面，水泥路面的照度要求可相应降低，降低幅度不超过 30%。

公路照明等级应根据与之相连的城市道路照明标准、公路交通控制系统和道路分隔设施来确定。

上述平均照度有两个标准值，以下情况应使用高标准值：

  1. 与具有高级照明标准的城市道路相连；
  2. 能见度低；
  3. 公路交通控制系统和道路分隔设施不足。
    当连接城市道路时，照明标准等级低，能见度好，且有足够的公路交通控制系统和道路分隔设施，公路照明应采用低等级值。

城市道路照明

LUXMAN - 1 人份

快速路和主干道 最低平均照度维持值为 20 lx（低标准）/30 lx（高标准），均匀度最低值为 0.4；

二级公路 最低平均照度维持值为 15 lx（低标准）/20 lx（高标准），均匀度为 0.4；
路侧：平均照度为 10 lx（低标准）/15 lx（高标准），均匀度为 0.3；

上述照度要求仅适用于沥青路面，水泥路面的照度要求可相应降低，降低幅度不超过 30%；

城市道路照明照度值应根据项目所在区域、道路定位、交通流量、道路分隔设施、环境亮度条件和实际需要确定。

以下情况应使用高标准值：

  • 中心城市和地区，或通往城市大型公共建筑和场所的主要道路；
  • 中央商务区或城市主干道；
  • 环境亮度较高的道路；
  • 供人们进出学校、医院和疗养院等地区的主要道路；
  • 道路分隔设施不足，机动车、非机动车和行人混合通行的道路。

建议在以下情况下使用低标准值：

  • 居民区和休闲区附近的道路；
  • 环境亮度较低的地区。

农村道路照明

太阳能路灯案例

主要道路 最低平均照度维持值为 10 lx（低标准）/15 lx（高标准），均匀度最低值为 0.3；

小街小巷 最低平均照度维持值 5 lx（低标准）/ 8 lx（高标准）；

公共活动广场： 最低平均照度维持值 10 lx（低标准）/ 15 lx（高标准）；

上述照度要求仅适用于沥青路面，水泥路面的照度要求可相应降低，降低幅度不超过 30%；

农村道路照明照度值应根据项目所在区域、道路定位、交通流量、道路分隔设施、环境亮度条件和实际需要确定。

以下情况应使用高标准值：

  • 城镇附近交通流量大的道路；
  • 商业活动密集的大型乡村公路；
  • 环境亮度较高的道路；
  • 道路分隔设施不足，机动车、非机动车和行人混行的道路

建议在以下情况下使用低标准值：

  • 偏远地区的乡村道路；
  • 不允许机动车通过的村内道路；
  • 环境亮度较低的地区。

交叉路口区域机动车力士水平

  • 1 级与 1 级、2 级、3 级的交叉点：最低平均照度维持值为 30 lx（低标准）/ 50 lx（高标准），均匀度维持值为 0.4；
  • 2 级与 2 级的交叉点，3 级：最低平均照度维持值为 20 lx（低标准）/30 lx（高标准），均匀度为 0.4；
  • 3 级与 3 级交叉：最低平均照度维持值为 15 lx（低标准）/20 lx（高标准），均匀度为 0.4；

当交叉道路的照明标准均为低标准照度值时，交叉区域应采用低标准值，否则应采用高标准值。

行人天桥照明 Lux 标准

  • 农村地区人流量大、城市人流量小的人行天桥：桥面平均照度为 5lx，楼梯通道平均照度大于 6lx；
  • 对于城市中人流量较大的人行天桥：桥面的平均照度为 10lx，楼梯通道的平均照度大于 12lx；
  • 半封闭式人行天桥：桥面平均照度为 30lx，楼梯通道平均照度大于 36lx；

联系我们获取免费路灯工程设计

    太阳能 LED 路灯

    太阳能 LED 路灯应用分析

    /于 /由

    When Greta Thunberg, a Swedish environmental teenager, chose to sail the Atlantic for two weeks before arriving in New York for the United Nations’ youth climate summit, Luxmanlight employees were actively promoting the use of Integrated Solar LED Street Lights around the world. Different views on the same event just represent our different ideas on environmental protection.

    "(《世界人权宣言》) all in one solar LED street light is the product of modern science and technology development. It directly uses solar energy for power supply, environment-friendly, and energy-saving. With the characteristics of once investment and long-term return, traditional street lamps and an LED street lamp is gradually replaced. The 太阳能路灯 with an automatic lighting system is generally used for street lighting of urban and rural roads. The intelligent street lighting system can realize the intelligent monitoring and management of street lights and reduce the operation and maintenance cost of the system. Thanks to its stable performance, easy management and no need for electricity connection, it is becoming more and more popular. Solar LED street lamps are used in parks, communities, squares, and parking lots from remote rural areas to cities. According to our customer’s experience, now we summarize the main installation locations of solar street lamps.

     

    Application location of solar LED street lamps

    1. Rural road lighting

    The rural natural environment is harsher, not suitable for laying cable. Solar lamp installation is simple, long service life. Moreover, rural roads are narrow and small, and the requirements for LED light sources are not high, which is suitable for installing stand-alone solar LED street lights.

    太阳能路灯太阳能路灯

    1. Monitoring and lighting of farms, barns, doorways, and courtyards

    House installation of 太阳能路灯 not only very convenient night lighting, but also can be equipped with a camera monitoring function. In the meantime, installation is simple, still can save a lot of electricity bills. Current standard configuration with light control, will according to illumination (brightness) automatically turn on-off the light, auto-off in the day, auto-on light at night, very simple and convenient.

    1. Homestay, resort, and hotel outdoor lighting

    Lighting safety, environmental protection, and energy-saving are the pursuit of the concept of homestay and hotel, so the solar street lamp is the right choice.

    1. Mining area, remote power shortage place lighting

    Mining areas are usually quite remote, so the cost of installing street lamps by cable is very high. Therefore, it is appropriate to choose a solar street lamp. Luxman solar LED street light works 12 hours a night and can support 5-7 rainy days. The road may still be rough, but it is no longer dark and safe to travel.

    1. Island lighting

    There is no doubt that islands are short of electricity, especially the remote, smaller islands, which are 100% short of electricity. Diesel power doesn’t work 24/7 and there are always dark hours, but solar lighting will keep your nights dark no matter how windy or rainy.

    LUXMAN - 太阳能路灯 1LUXMAN - 太阳能遥控区域灯

    1. Monitoring and lighting of the home town villa

    Many young people like to live in the city, where the house is only for old people and children or no one lives. Therefore, a kind of solar street light with a camera that can be illuminated and monitored is very suitable for use. like Luxman S3C Series solar street light with a camera for residential areas.

    1. The lighting of urban roads and secondary trunk road

    Energy-saving and emission reduction can be achieved not only by using AC Powered LED lighting, but also by using more advanced solar-powered street lighting without electricity bill, which can be invested once and be effective for a long time.

    1. Square, parking lot, playground lighting

    There’s a lot of traffic in public places, but it’s usually only in the early hours of the night. The intelligent solar street lamp can do induction mode(PIR), time control mode, and can also do induction + time control hybrid mode, so it can meet the lighting use in public places.

    1. Schools, hospitals and museums outdoor lighting

    Environmental protection is everyone’s business. The low-carbon concept must be promoted from schools to hospitals, exhibitions, museums, and another outdoor lighting. Integrated solar street lamps not only meet the lighting needs but also have a prominent environmental protection demonstration effect.

    太阳能车库灯太阳能校园照明

    1. Park and green space lighting

    In general, the lighting of parks and green Spaces does not require high illumination on the ground (compared with outdoor stadium lighting). Intelligent solar street lamps are the best choice for lighting in these public areas.

    1. Community road lighting

    The lighting of community roads and garden roads in the community has changed from traditional lamps to LED lamps and then to solar street lamps, which is the trend of the times.

    1. Industrial zone, science, and technology park, road lighting

    In industrial areas, science and technology parks or innovation incubators park, no matter traditional lighting or LED lighting which used for public electricity, it is not as cost-effective as solar street lamps after cost accounting.

    13.Outdoor camping lighting

    The installation of LED solar street lamps in some of the best places for camping not only solves the main problem of campers but also ensures their safety to some extent.

    In the future, more than 70% of roads and lighting are expected to use solar street lamps, compared with less than 5% today. At present, the price of a solar street lamp is mainly set according to the level of parameter configuration, and the service life is closely related to the configuration. The solar street light manufacturer offers a five-year warranty, which is favored by many customers.

    Possibly-related posts:

    相关文章

    https://luxmanlight.com/how-to-choose-the-best-solar-street-light-factory-in-china//

    请通过下面的表格与我们联系。谢谢！

    5 + 3 = ?

    太阳能路灯制造商

    中国最好的太阳能路灯制造商是哪家？

    /于 /由

    With the rising consumer’s inclination, towards eco-friendly, renewable, and energy-saving lighting products, more and more solar street light manufacturers in China are crowding into the solar street lighting industry now.

    According to the solar street light market report, the global solar street lighting market was valued at approximately USD 4.25 billion in 2017 and is expected to generate revenue of around USD 18.31 billion by the end of 2024. The Solar Lighting Market is prompting demand growth both in the consumer and manufacturer.

    太阳能动力感应灯制造商

    So how to be the best solar street light factory in China?

    First,own Years of Production and Manufacturing Experience

    It is very important to have a stable supply chain system for the production of 太阳能路灯, because some key components of solar street lamps, such as batteries, solar cells, solar controllers, and so on, are decisive factors for product performance and lifetime. If the supply chain system is unstable, it will directly affect product quality & lifetime.

    In addition, the solar street lamp is a small solar power generation system, which seems to be a simple product, but in fact, the assembly of a system product is not as simple as the assembly of product parts. In addition to good product components, a good solar power generation system should also pay attention to its system operation status, such as controller, the precision of procedure, battery protection function, a setting of light mode, and so on.

    The control of processing technology is also very important. If you have many years of production and manufacturing experience, you will have a good running-in both from the product supply chain and product performance, and you can OEM and ODEM solar street light, which is based on years of production and manufacturing experience, and practical application and installation experience and data in the past few years, so as to produce more stable and more consistent products as market demand.

    Second, good quality control ability

    Any good products can not be separated from strict quality control; otherwise, the products manufactured will not be able to ensure that it is a qualified product. As a good all-in-one solar street light manufacturer, series of quality control should be carried out from the quality of incoming materials, the quality in the process of production and processing, and the quality of the shipment to ensure that each product is qualified from raw material to the customer. Hence, a top solar street light manufacturer must have a strict quality control system.

    luxman contact

    Third, responsible after-sales service

    In 卢克斯曼, the sale of a product is only the beginning of sales. We will track the products sold from logistics to installation and during use. We have an ID bar code tracking system for all the products delivered. If there is a problem, we can trace the source material to installation quickly. We pay great attention to the customer’s experience about the use of our products, regularly understand customer feedback and final consumer feedback on the use of our products, and minimize customer investment in after-sales. Customers in the purchase of our products, without worries, are our goal and direction of efforts.

    Fourth, leading technology

    Now the solar street lamp products have developed, from the first generation split type and the second generation half-split type to the third generation one-in-one type.

    The third-generation product of integrated solar street lamp, whether from product design, performance, product quality, product cost-effectiveness, has made a leap forward. At present, the third generation of integrated solar street lamp is much more intelligent. It can adjust and programmed the light mode, brightness, and so on through a remote control switch. Some intelligent products can be connected with APP, monitor the working parts of the product in real-time on the mobile phone, and know the working status of the product in time. What’s more, with proven technology, the CCTV camera is connected with the solar street light providing surveillance for 7*24hours.

    A best solar street light manufacturer invests more in R&D because if he has good product technology, he will have a more competitive advantage in the market.

    The above aspects are about what kind of manufacturer is good solar-led street light manufacturers, and one of them is that a good all-in-one solar street light manufacturer is very concerned about the user experience.

    相关文章

    https://luxmanlight.com/how-to-choose-the-best-solar-street-light-factory-in-china//

    如需咨询，请联系我们！

    4 + 4 = ?

    太阳能路灯

    太阳能路灯的 5 种应用 -LUXMAN LIGHT

    /于 /由

    As we know Solar Street light has the following benefits:

    * Installation anywhere

    * Maintenance-free

    * No underground or overhead service

    * No electricity bill

    * Different styles available

    * Mobile phone remote control

    * Real-time 24 hours of surveillance and security function optional

     

    From the above advantages of solar-powered street lights, it can have a wide application, so in what areas can all in one solar light be applied?

    Solar-Street-Light-Applications

    1st– Remote Areas

    Such as rural roads, islands, military barracks, farms and so on, because these places are remote or inhabitants do not live centrally, so the laying of electric wiring is very difficult, the cost of laying wiring is not proportional to the utilization rate, so solar pole lights can be used in remote areas.

    2nd – Construction Site

    Because these are temporary places, so access to power or installation of lighting is inconvenient, LUXMAN once had a customer who bought LUXMAN all in one solar street lights is leased to large local builders.

    3rd – Campus, Square

    Generally, these places are very empty, have a better sunshine foundation, on the other hand, the flow of people in these areas will be more during 6pm-10pm, and later will be reduced a lot, solar streetlight sensing and timing control functions well meet this demand characteristics.

    4th – Road and Street

    This application is also the most important application, street light power consumption is usually relatively large, in some countries and regions, electricity is very expensive, if the solar street lamp can be used to replace ordinary street light or LED street light, then a huge cost will be saved.

    5th Residential Areas

    Solar street lamps have good mobility. Residents can install different places according to their needs, such as swimming pool, Party table, courtyard entrance, Parking lot, etc. In addition, the extension function of solar street lamps can also meet the needs of residents, such as camera monitoring function, USB charging, mobile phone APP operation function and so on, bring users a more convenient user experience.

     

    本文由 LUXMAN LIGHT 原创。未经许可，请勿转载。

    最近的更新

    <>暴雨引发路灯触电事故分析

    <>SMART STREET LIGHT AND 5G MICRO STATION

     

    有关绿色能源、照明知识的更多信息，请访问：

    www.luxmanlight.com

    太阳能路灯

    暴雨引发路灯触电事故分析

    /于 /由

    Every summer during the rainstorm season, news of casualties caused by street light electric shock accidents occurs. Most of the Electric Shock of Street Light caused by light electric leakage on rainy days. Due to the high temperature and humidity of street light facilities in summer, the cable insulation layer is easy to aging and breakdown, leading to electric leakage. In addition, thunderstorms Street light Leakage Accident occur frequently in summer, it forms water accumulation on roads, which immerses urban lighting facilities (such as cable wells, street light poles, etc.) in water and easily causes electric leakage accidents. The leakage of the street light pole may occur in the following ways.

    LED 路灯street light

    • The poor quality construction causes leakage of lighting facilities.

    Failure to comply with the standard construction or installation quality problems, such as screw damage to the insulation layer of street light cables during installation. In rainstorm days, when urban rainwater soaks live equipment, it will cause the connection equipment live. Leakage caused by rainwater immersion.

    street light poles LUXMAN - LED Street Light Pole

    •   The aging and damage of the cable insulation layer in the lamp pole make the lamp pole live.

    Some construction simply uses a tape winding method, the tape is easy to aging, it is likely to leak electricity.

    • The poor quality of lighting electrical appliances causes the lamp pole to be electrified.

    In the design and construction of urban lighting engineering, strict checks should be made on the selection of lighting appliances, the selection of certified light sources, electrical appliances, lamps, and other products should be a priority.

    • Discharge of wiring terminals.

    At present, most of the wiring connection modes are peeling and winding. This mode has high resistance, high current, short heating life of terminals, and will discharge when moisture or water is immersed.

    • The electricity of the lamp pole caused by man-made destruction.

    It mainly refers to the cable which was stolen and damaged, cable fracture exposed to the lamp pole, and this easily leads to discharge accidents.

    • The harsh natural environment causes the lamp pole to be charged.

    Because of thunderstorms, water overflowed the repair door holes, resulting in street light leakage. Or lightning strike on the lamp pole, because the lamp pole grounding is not good, resulting in burning electrical equipment so that the lamp pole around to be charged.

    At present, more and more 太阳能路灯 used for roadway lighting, which completely solved the leakage accident. In addition to urban main roads, major facilities, buildings, large squares and other places such as secondary roads, residential roads, parking lots, parks, schools, hospitals, and so on, all of these places can consider the use of solar street lights. In addition, in some natural disaster-prone areas, such as flood areas and earthquake-prone areas, solar street lights are also a good choice because these disasters are easy to cause line damage and leakage.

     

    相关文章

    https://luxmanlight.com/how-to-choose-batteries-for-your-solar-street-light-project/

    请通过下面的表格与我们联系。谢谢！

    0 + 7 = ?