标签存档: 太阳能路灯

勒克斯级别

太阳能路灯照度标准。我需要什么照度?

太阳能街道照明系统的光测量

亮度有两个重要指标 太阳能路灯、拉克斯(Lux)和流明(Lumens)。
勒克斯和流明都是亮度的测量单位。它们用来告诉我们特定表面的照明输出量和光照亮度。

流明等于光输出。
勒克斯(用 lx 表示)代表单位面积的光通量。

流明和勒克斯之间的关系:1 勒克斯等于每平方米 1 流明(lm/m2)。
流明和流明在本篇文章中,我们将探讨路灯的流明标准及其重要性。如果您想了解流明,可以查看这篇文章:了解瓦特和流明:如何为项目选择合适亮度的灯具

什么是照明中的勒克斯,为什么它很重要?

勒克斯是对落在物体表面的光通量的测量。勒克斯是光度学的国际单位,是一种测量光强度的方法。勒克斯用于指定光或照明的亮度。它是所有类型照明(如家用照明、办公室照明、汽车前灯或路灯)的标准光测量单位。

道路照明标准

为什么勒克斯水平比流明更有意义

流明测量单个光源的光输出。流明测量的计算方法是用光源的瓦数乘以每瓦光源的额定流明。

勒克斯是表面上的光量。这可以通过光传播一定距离后的亮度来测量。

除了亮度之外,勒克斯级也是测量太阳能路灯亮度的最佳方法。照度测量只需使用照度计即可轻松完成,而亮度测量则需要专业设备,实施起来较为困难。
现在,如果有一个亮度为 1000 流明的太阳能路灯灯泡,将其放置在 10 米之外,其亮度就会不同。因此,改变灯泡的位置会改变不同勒克斯水平下的亮度。流明测量灯泡产生的光量,勒克斯测量光传播的距离。

不同道路太阳能路灯照明的 Lux 值

我需要多高的照度?

根据一些国家政府文件规定的标准,我们提出以下建议作为参考:

公路照明 勒克斯级别

太阳能路灯

一级公路、二级公路最低平均照度维持值为 20 lx(低标准)/30 lx(高标准),均匀度最低值为 0.4;

三级公路最低平均照度维持值为 15 lx(低标准)/20 lx(高标准),均匀度为 0.4;
四级道路:平均照度 10 lx(低标准)/15 lx(高标准),均匀度 0.3;

上述照度要求仅适用于沥青路面,水泥路面的照度要求可相应降低,降低幅度不超过 30%。

公路照明等级应根据与之相连的城市道路照明标准、公路交通控制系统和道路分隔设施来确定。

上述平均照度有两个标准值,以下情况应使用高标准值:

  1. 与具有高级照明标准的城市道路相连;
  2. 能见度低;
  3. 公路交通控制系统和道路分隔设施不足。
    当连接城市道路时,照明标准等级低,能见度好,且有足够的公路交通控制系统和道路分隔设施,公路照明应采用低等级值。

城市道路照明

LUXMAN - 1 人份

快速路和主干道 最低平均照度维持值为 20 lx(低标准)/30 lx(高标准),均匀度最低值为 0.4;

二级公路 最低平均照度维持值为 15 lx(低标准)/20 lx(高标准),均匀度为 0.4;
路侧:平均照度为 10 lx(低标准)/15 lx(高标准),均匀度为 0.3;

上述照度要求仅适用于沥青路面,水泥路面的照度要求可相应降低,降低幅度不超过 30%;

城市道路照明照度值应根据项目所在区域、道路定位、交通流量、道路分隔设施、环境亮度条件和实际需要确定。

以下情况应使用高标准值:

  • 中心城市和地区,或通往城市大型公共建筑和场所的主要道路;
  • 中央商务区或城市主干道;
  • 环境亮度较高的道路;
  • 供人们进出学校、医院和疗养院等地区的主要道路;
  • 道路分隔设施不足,机动车、非机动车和行人混合通行的道路。

建议在以下情况下使用低标准值:

  • 居民区和休闲区附近的道路;
  • 环境亮度较低的地区。

农村道路照明

太阳能路灯案例

主要道路 最低平均照度维持值为 10 lx(低标准)/15 lx(高标准),均匀度最低值为 0.3;

小街小巷 最低平均照度维持值 5 lx(低标准)/ 8 lx(高标准);

公共活动广场: 最低平均照度维持值 10 lx(低标准)/ 15 lx(高标准);

上述照度要求仅适用于沥青路面,水泥路面的照度要求可相应降低,降低幅度不超过 30%;

农村道路照明照度值应根据项目所在区域、道路定位、交通流量、道路分隔设施、环境亮度条件和实际需要确定。

以下情况应使用高标准值:

  • 城镇附近交通流量大的道路;
  • 商业活动密集的大型乡村公路;
  • 环境亮度较高的道路;
  • 道路分隔设施不足,机动车、非机动车和行人混行的道路

建议在以下情况下使用低标准值:

  • 偏远地区的乡村道路;
  • 不允许机动车通过的村内道路;
  • 环境亮度较低的地区。

交叉路口区域机动车力士水平

  • 1 级与 1 级、2 级、3 级的交叉点:最低平均照度维持值为 30 lx(低标准)/ 50 lx(高标准),均匀度维持值为 0.4;
  • 2 级与 2 级的交叉点,3 级:最低平均照度维持值为 20 lx(低标准)/30 lx(高标准),均匀度为 0.4;
  • 3 级与 3 级交叉:最低平均照度维持值为 15 lx(低标准)/20 lx(高标准),均匀度为 0.4;

当交叉道路的照明标准均为低标准照度值时,交叉区域应采用低标准值,否则应采用高标准值。

行人天桥照明 Lux 标准

  • 农村地区人流量大、城市人流量小的人行天桥:桥面平均照度为 5lx,楼梯通道平均照度大于 6lx;
  • 对于城市中人流量较大的人行天桥:桥面的平均照度为 10lx,楼梯通道的平均照度大于 12lx;
  • 半封闭式人行天桥:桥面平均照度为 30lx,楼梯通道平均照度大于 36lx;

联系我们获取免费路灯工程设计

    太阳能照明项目

    什么是最好的太阳能电池

    近年来,由于太阳能具有绿色能源、安装简便、应用广泛等优点,可以安装在偏远地区,无需连接电网、 太阳能路灯 正等待着越来越多的安装和使用。如何为您的项目选择合适的太阳能蓄电池?LUXMAN 总结多年经验,为您做出以下分析:

    啫喱电池

    适用于分体式太阳能路灯。早期的分体式太阳能路灯主要由太阳能电池板 + 电池组件 + LED 灯具组成。其中,太阳能电池板需要配备固定支架,硒鼓蓄电池需要装在蓄电池箱内,埋在地下或挂在灯杆上。配置的 LED 灯一般需要一定长度的布线。安装不便,产品成本和人工成本较高。

    太阳能路灯电池

    锂电池

    目前,分体式太阳能路灯多采用锂电池盒技术,即把锂电池组和控制器装进一个盒子里,通常放在太阳能电池板的背面,有的则放在LED灯的底部,采用智能控制系统。

    太阳能电池

    锂电池组,目前常用的锂电池有 18650、26650 和 32650 三种。 相对来说,18650 通常是三元锂电池,无论使用寿命和性价比都不高。目前,常用的磷酸铁锂电池规格有 26650 和 32650 两种。26650 表示直径 D=26mm,长度 L=65mm;32650 表示直径 D=32mm,长度 L=65mm。由于电池尺寸的限制,26650 的电池容量没有 32650 高,使用 32650 实现相同配置的电池数量也少于 26650。

    例如,80 瓦集成太阳能路灯需要 12.8V 72AH LIFEPO4 电池。26650 电池容量为 4000mah,32650 电池容量为 6000mah。如果 12.8V 72AH 电池组使用 26650,则需要 4S18P 72 个电芯,32650 则需要 4S12P 48 个电芯。在配置相同的情况下,使用 32650 的电池数量将比使用 26650 少 24 个。在价格方面,目前 26650 电池 1AH 的价格约为人民币 20.00 元,而 32650 电池 1AH 的价格约为人民币 14.00 元。在这种情况下,如果使用 26650 电池,电池组成成本为 72*20=1440.00 元人民币,而使用 32650 电池的成本为 72*14=1008.00 元人民币,成本差距明显。因此,32650 的性价比较高。

    总之,太阳能路灯的蓄电池首先必须根据项目的技术要求进行配置,但也必须考虑产品的成本。

    使用大容量磷酸铁锂电池是一种趋势。太阳能路灯的成本会越来越低,但质量取决于工厂的生产技术和对原材料的控制能力。

    对于外观相同的产品,价格越低越要谨慎,因为正规厂家使用的都是优质原材料,优质原材料的价格不会太便宜。 LUXMAN 太阳能路灯 我们使用高质量的原材料,在过去几年中,我们的质量得到了客户的肯定。
    相关文章

    https://luxmanlight.com/how-to-choose-the-best-solar-street-light-factory-in-china//

    如需咨询,请联系我们!

    2 + 1 = ?

    集成式太阳能 LED 灯

    如何制作太阳能路灯模型?

    每个项目都有自己的目标,当我们谈到 太阳能路灯太阳能路灯的目标是成为传统路灯的绿色替代品。为了最大限度地提高太阳能路灯的效率,每个组件都需要在最大限度地利用能源的同时将损耗降到最低。考虑到太阳能路灯的型号,你可能会想到许多不同的设计和结构。虽然基本设计保持不变,但不同变体的太阳能路灯在美学上有所不同。让我们来讨论一下如何制作一个简单的太阳能路灯模型。

    通常有七个主要部分组成一个完整的太阳能路灯模型包:

    • 太阳能电池板,又称太阳能光伏电池 - 用于将太阳能转化为电能
    • 太阳能充电控制器 - 用于控制或调节从光伏组件到蓄电池的电荷流
    • 电池组 - 用于储存电荷,供夜间使用
    • 路灯 - 光源
    • 杆 - 用于不同部件之间的连接和安装在高架上
    • 远程控制器 - 帮助控制、管理和维护太阳能路灯模型

    根据制造商的不同,组件类型也可能不同。

    太阳能路灯

     

    设计太阳能路灯模型

    首先,计算照亮该区域所需的光量。所使用的灯泡将帮助您了解瓦特数。使用该瓦数和照明持续时间来计算电池和任何耗电组件的瓦时。瓦时将帮助您选择能够产生该能量的光伏组件。请牢记能量损耗,并始终选择能产生比补偿损耗所需更多能量的光伏电池板。角度和瓦特峰值取决于安装位置,因此要对此进行检查。

    要想知道使用多大的电池,灯光所需的瓦特小时数可以帮您解决这个问题。利用一些基本的电学公式,您可以找出电池的充电深度、标称电量和电池容量(以安培小时为单位)。

    充电控制器的大小取决于电池板的功率要求和您选择的储能装置。基本原则是使用能够处理电池板电流的充电控制器。

    组装太阳能电池板

    太阳能电池板由半导体制成;半导体是一种在某些条件下能够导电的物质。通常使用的材料是硅,但也有其他材料,如砷化镓、磷化铟和硒化铜铟。要制造太阳能电池,需要数以万亿计的硅原子形成硅片层。每个硅原子都含有极其微小的电子。这些微小的电子带有电荷。当阳光照射到电池上时,阳光中的光子会让电子从原子中释放出来,当电子在电池中流动时,就会产生电能。

    太阳能电池板通过电缆连接到灯杆和太阳能照明系统的其他组件上。支架和框架用于固定太阳能电池板。这些支架通常由铝制成,重量轻且不受天气影响。

    组装电池

    电池组件通过导线与光伏组件和 LED 灯连接。电池设计高效,可长时间持续供电。电池组件通常装在一个铝制外壳内,外壳上开有通风口,以保持通风,散发电池产生的热量。

    LED 灯具

    LED 灯具通过支架固定在灯杆上,LED 灯具的高度可以调节,以获得适当的灯光亮度。LED 灯具有多种设计,适用于不同类型的太阳能灯。

    提高系统效率

    为了优化整个系统,需要谨慎选择某些组件。首先是使用 LED 灯代替荧光灯,以降低能耗。

    使用最佳的电池组存储技术。在大多数情况下,太阳能系统通常推荐使用锂离子电池。还有一些其他技术,如铅酸电池、胶体电池等。

    使用单晶光伏组件,因为与多晶组件相比,单晶组件效率更高。

    选择高效的线路连接,将系统中的能量损失降至最低。您使用的控制器应能有效地开启和关闭系统。

    使用智能传感器

    太阳能照明系统可配备以下智能控制器和几个传感器,以提高其效率。被动红外传感器,用于检测运动并控制照明度。使用安装了运动传感器的太阳能灯可以有效地探测到屋外的任何活动,因为它会立即向人或物体照射光线。还有其他运动传感器,如微波运动传感器、双技术传感器等。

    电池监测

    这有助于防止电池受损。当电池感应到过充时,它会简单地减少能量流;当由于阳光强度下降或突然用电量增加而导致电压下降时,它可以保持适当的电压调节。

     

    太阳能 LED 路灯

    太阳能 LED 路灯应用分析

    When Greta Thunberg, a Swedish environmental teenager, chose to sail the Atlantic for two weeks before arriving in New York for the United Nations’ youth climate summit, Luxmanlight employees were actively promoting the use of Integrated Solar LED Street Lights around the world. Different views on the same event just represent our different ideas on environmental protection.

    "(《世界人权宣言》) all in one solar LED street light is the product of modern science and technology development. It directly uses solar energy for power supply, environment-friendly, and energy-saving. With the characteristics of once investment and long-term return, traditional street lamps and an LED street lamp is gradually replaced. The 太阳能路灯 with an automatic lighting system is generally used for street lighting of urban and rural roads. The intelligent street lighting system can realize the intelligent monitoring and management of street lights and reduce the operation and maintenance cost of the system. Thanks to its stable performance, easy management and no need for electricity connection, it is becoming more and more popular. Solar LED street lamps are used in parks, communities, squares, and parking lots from remote rural areas to cities. According to our customer’s experience, now we summarize the main installation locations of solar street lamps.

     

    Application location of solar LED street lamps

    1. Rural road lighting

    The rural natural environment is harsher, not suitable for laying cable. Solar lamp installation is simple, long service life. Moreover, rural roads are narrow and small, and the requirements for LED light sources are not high, which is suitable for installing stand-alone solar LED street lights.

    太阳能路灯太阳能路灯

    1. Monitoring and lighting of farms, barns, doorways, and courtyards

    House installation of 太阳能路灯 not only very convenient night lighting, but also can be equipped with a camera monitoring function. In the meantime, installation is simple, still can save a lot of electricity bills. Current standard configuration with light control, will according to illumination (brightness) automatically turn on-off the light, auto-off in the day, auto-on light at night, very simple and convenient.

    1. Homestay, resort, and hotel outdoor lighting

    Lighting safety, environmental protection, and energy-saving are the pursuit of the concept of homestay and hotel, so the solar street lamp is the right choice.

    1. Mining area, remote power shortage place lighting

    Mining areas are usually quite remote, so the cost of installing street lamps by cable is very high. Therefore, it is appropriate to choose a solar street lamp. Luxman solar LED street light works 12 hours a night and can support 5-7 rainy days. The road may still be rough, but it is no longer dark and safe to travel.

    1. Island lighting

    There is no doubt that islands are short of electricity, especially the remote, smaller islands, which are 100% short of electricity. Diesel power doesn’t work 24/7 and there are always dark hours, but solar lighting will keep your nights dark no matter how windy or rainy.

    LUXMAN - 太阳能路灯 1LUXMAN - 太阳能遥控区域灯

    1. Monitoring and lighting of the home town villa

    Many young people like to live in the city, where the house is only for old people and children or no one lives. Therefore, a kind of solar street light with a camera that can be illuminated and monitored is very suitable for use. like Luxman S3C Series solar street light with a camera for residential areas.

    1. The lighting of urban roads and secondary trunk road

    Energy-saving and emission reduction can be achieved not only by using AC Powered LED lighting, but also by using more advanced solar-powered street lighting without electricity bill, which can be invested once and be effective for a long time.

    1. Square, parking lot, playground lighting

    There’s a lot of traffic in public places, but it’s usually only in the early hours of the night. The intelligent solar street lamp can do induction mode(PIR), time control mode, and can also do induction + time control hybrid mode, so it can meet the lighting use in public places.

    1. Schools, hospitals and museums outdoor lighting

    Environmental protection is everyone’s business. The low-carbon concept must be promoted from schools to hospitals, exhibitions, museums, and another outdoor lighting. Integrated solar street lamps not only meet the lighting needs but also have a prominent environmental protection demonstration effect.

    太阳能车库灯太阳能校园照明

    1. Park and green space lighting

    In general, the lighting of parks and green Spaces does not require high illumination on the ground (compared with outdoor stadium lighting). Intelligent solar street lamps are the best choice for lighting in these public areas.

    1. Community road lighting

    The lighting of community roads and garden roads in the community has changed from traditional lamps to LED lamps and then to solar street lamps, which is the trend of the times.

    1. Industrial zone, science, and technology park, road lighting

    In industrial areas, science and technology parks or innovation incubators park, no matter traditional lighting or LED lighting which used for public electricity, it is not as cost-effective as solar street lamps after cost accounting.

    13.Outdoor camping lighting

    The installation of LED solar street lamps in some of the best places for camping not only solves the main problem of campers but also ensures their safety to some extent.

    In the future, more than 70% of roads and lighting are expected to use solar street lamps, compared with less than 5% today. At present, the price of a solar street lamp is mainly set according to the level of parameter configuration, and the service life is closely related to the configuration. The solar street light manufacturer offers a five-year warranty, which is favored by many customers.

    Possibly-related posts:

    相关文章

    https://luxmanlight.com/how-to-choose-the-best-solar-street-light-factory-in-china//

    请通过下面的表格与我们联系。谢谢!

    0 + 6 = ?

    太阳能路灯项目

    什么是太阳能路灯?

    With global warming, green energy has become a trend. Solar-powered street lights with 100% green energy come into being, so what is solar-powered street lights? 太阳能路灯 are mainly composed of solar panels, controllers, LED light sources and batteries.
    During the day, solar panels absorb energy from the sun and convert it into power, which is stored in solar batteries by the controller, and provide lighting power for an LED light source at night. This is the working principle of solar street lamps work.

    solar-powered-street-lights

    Solar Street Light Advantages:

    * Installation anywhere

    * Maintenance-free

    * No underground or overhead service

    * No electricity bill

    * Different styles available

    * Mobile phone remote control

     

     

    本文由 LUXMAN LIGHT 原创。未经许可,请勿转载。

    最近的更新

    <>How long do solar-powered street light last-LUXMAN Light

    <>5 Kinds of Solar Street Light Applications

     

    有关绿色能源、照明知识的更多信息,请访问:

    www.luxmanlight.com